AQUAFIN®-2C

2-component, flexible, polymer modified, Cementitious Waterproofing

Properties:

AQUAFIN-2C= is a flexible, 2-component, polymer modified, cement-based waterproof protective coating. It has an excellent adhesion, abrasion resistance, weatherproofing & waterproofing properties providing seamless protective coats

Key Features and Benefits:

Easy fo use and to apply
Environmentally friendly
UV-stable
Resists hydrostatic pressure (> 5 bars}
Crack bridging ability
Flexible Enables substrates to breathe
Can be applied to damp surfaces
Abrasion resistant
Selt-curing
Active barrier to Carbon Dioxide (CO9}
Stands up to pedestrian and light traffic

Uses:

AQUAFIN-2C is an economic, flexible polymer modified cement-based protective coating for above & below grade, horizontal or vertical surfaces for:
1. Water structures
2. Sewage treatment plants
3. Basement walls
4. Balconies, plaza deck
5. Underneath tile adhesive mortars (showers, sanitary
  rooms, kitchens, swimming pools, etc.]
6. Wastewater treating plants
7. Reinforced concrete structures
8. Water tanks and reservoirs
9. All similar works
AQUAFIN-2C is a stancalone product. It can be used exposed or over-coated with flexible or rigid mortars (use a separation layer), stuccos or coatings for uniform appearance. It bridges shrinkage cracks. Larger static {non-moving) or dynamic {moving) cracks can be sealed with ASO-JointTape-2000 or ASO-Joint
Tape-2000-S in conjunction with AQUAFIN-2C.

Product Exposure:

Positive side waterproofing 1,5 – 2,5 mm:

Apply AQUAFIN-2C in two coats as specified. Apply the second coat (or multiple coats} as soon as the first coat has sufficiently hardened or wait until next day.
Negative side waterproofing 2,5 mm:
Apply Ist coat with AQUAFIN-1K at 2 kg/m* Apply 2nd coat with AQUAFIN-2C at 3 kg/m?

EXPOSURE*} OF APPLICATION TO:

rain, vertical surfaces, after approx. 3 hrs
rain, horizontal surfaces, minimum 6 hrs
foot traffic after approx 1day
tile mortar and tiles after approx 1 day
hydrostatic pressure after reaching Shore A Hardness 85 (between 3-7 days]
back filling after aoprox. 3 days “) at +20 ° C and 60% humidity

Technical Specifications:

All data are averages of several tests under laboratory conditions. In practice, climatic variations such as temperature, humidity, and porosity of substrate may affect these values.
Mixing ratio: 25 kg powder (comp. |} to 10
kg liquid {comp. Il}
Permeability: resistant up to 50m water head (positive side}
Water vapour diffusion p-value: 1000
Adhesive strength: O06N/mm² at 28d
Tensile elongation: 30 % at +20 °C

Product Application:

The substrate must be sound, clean, and free from voids, gaping cracks or ridges and open pored [like fine sand paper]. Remove bond breakers, such as oil, grease, dirt, loose particles, remains of form oils, water repellents, rust or other coatings by water blasting or wet or dry sandblasting. Repair holes, defects, irregular surfaces, weak mortar joints, etc. with a patching mortar. Round edges at vertical external joints. Close large open pores and joint recesses of CMU blocks and joint unevenness in brick walls with sand/cement mortar before applying AQUAFIN-2C.

Pre-dampen all absorbtive substrates (excluding drywall or similar} with clean water to saturated surface dry (SSD} condition prior to application. Remove all standing surface water. Seal dry, dusty or very absorptive surtaces (i.e. drywall, gypsum} with one coat liquid component, diluted with water 1:4 to 1:5.

A. Mixing ratio by weight:
25 kg powder to 10 kg liquid
B. Mixing ratio by volume:
approximately 2.5 parts powder to | part liquid.

Pour UNIFLEX-2C liquid into a clean container, add AQUAFIN-2C powder and stir to a lump free creamy consistency with a strong, slow speed (300 rom} mechanical mixer.

NOTE: Do not apply AQUAFIN-2C at temperatures below +5 °C.

Product Requirements:

At high temperatures, i.e. +30 °C and above, protect application from direct sun and wind to prevent premature surface drying and shrinkage cracks. Apply material in 2 (two) coats minimum. AQUAFIN-2C may be applied by brush, roller, trowel or appropriate compressed-air spray equipment. Surface can be left brushed or smooth troweled, depending on type of application and project specifications. Do not pre-dampen brush or roller with water. Quantities are dependent on the amount of protection desired. Horizontal and vertical joints: Seal horizontal wall4loor joints and internal vertical corners with ASO-JointTape-2000. Alternative: form cove (minimum 40 x 40 mm} with cement mortar. Static cracks greater than 1,0 mm: Repair static cracks >1,Omm width with ASO-JointTape-2000, or rout (cut) out and fill with ASOCREFRN and cover with AQUAFIN-2C, reinforced with AQUAFIN matt. Dynamic cracks and joints: Seal dynamic cracks and expansion joints with ASO-JointTape-2000-S.